070201/0 kit n7 page 1/5 user guide for fhs 40-p current transducer fhs 40-p kit 7 (g2.00.23.106.0) evaluation pcb connectors pin-out the board has two single row connectors j1 and j2. ? the four pin one (j1) makes possible to supply t he board and access to the output voltage easily. it has the following pin-out: pin # name description j1 connector 1 v ref reference voltage input/output 2 v out output voltage is proportional to current in the pcb track, v out = v ref + g i * i p note that the output voltage is positi ve when the current flows inside the tracks according to the direction marked ? i p ? ? on the pcb 3 0 0 v 4 v c positive supply voltage 4.75-5.25v; typical consumption 15 ma ? the two pin one (j2) makes possible to access to the fast output voltage and standby input easily. it has the following pin-out: pin # name description j2 connector 1 v outfast v outfast , fast output signal; note that this output is opposite to v out (see datasheet for connection) 2 standby standby, set operating or standby modes (see datasheet for connection) manufacturer and reference for j1, j2: preci-dip, 310-13-120-41-001001. thermal capability the enclosed evaluation pcb has tracks with thickness of 70 m. the dimensions of the tracks drawn on the evaluation pc b lead to some limitations on the maximum continuous current which can go through the pcb track. remark: under normal operating conditions, temperature of some parts of this product might exceed 70c.
070201/0 kit n7 page 2/5 primary track dimensions: thermal simulation cu 70 m: track thickness 70 m, pcb thickness 1.6 mm, t a = 85c, natural convection, i pn = 10 a rms or a dc. parameters value [mm] lx 21.22 ly 16.32 l_center 5.23 l_cone 2.5 w_center 0.78 w_piste 3 gap_piste 0.33 th_piste 0.07
070201/0 kit n7 page 3/5 the following figures should be taken into account to avoid overheating: (t primary track = 115 c) cu 35 m cu 70 m maxi rms current i pn [a] t a [c] ? t [c] t a [c] ? t [c] 0 115 0 115 0 2 104.7 10.3 110.6 4.4 4 72.8 42.2 97.1 17.9 5 48.2 66.8 86.9 28.1 6 18 97 74.3 40.7 8 na na 41.8 73.2 t y pical primar y current for a maximum track temperature of 115c (natural convection) 0 2 4 6 8 25 50 75 100 125 ambient temperature (c) primary current (arms) 70 microns cu 35 microns cu
070201/0 kit n7 page 4/5 connect then the primary between pins i p in and i p out. features magnetic field sensitivity typical 600 mv/mt current sensitivity typical 186.1 mini (typ-3 ): 181.8 maxi (typ+3 ): 190.4 mv/a measuring range typical 11 unless maxi rms current reached, see thermal capability a frequency range dc ? 100k hz l insertion 37 nh isolation characteristics symbol unit value rms voltage for ac isolation test, 50-60 hz, 1 min v d kv 0.8 impulse withstand voltage 1.2/50 s v w kv 1.4 creepage / clearance distance dcp/dci mm 0.4 comparative tracking index (pcb fr4) cti v 200 i p in i p out
070201/0 kit n7 page 5/5 application example according to en 50178 and iec 61010-1 standards and following conditions: ? rated isolation voltage 50 v (iec 61010-1) ? reinforced isolation ? over voltage category ov iii ? pollution degree pd1 ? non-uniform field safety this transducer must be used in electric/electronic equipm ent with respect to applicable standards and safety requirements in accordance with the manufacturer's operating instructions. caution, risk of electrical shock when operating the transducer, certain parts of the module can carry hazardous voltage (eg: primary busbar, power supply). ignoring this warning can lead to injury and/or cause serious damage. this transducer is a built-in device, whose conducti ng parts must be inaccessible after installation. a protective housing or additional shield could be used. main supply must be able to be disconnected.
|
